667 lbs. Rotary Tillers need to be heavy in order for the
tines to penetrate the ground, and reduce bucking.
5" to the right of center. The tiller is offset from the center of
the PTO so that you don't end up with compacted tire tracks in you finished
Forward, same rotation as the tires of the tractor when
traveling forward. This rotation requires less horsepower to operate;
allows for a smoother bed of soil behind the tiller, and allows rocks to
expel without recycling them through the tiller.
Adjustable side runners to 8" deep. Adjustable and replaceable
side runners allow for deep tilling.
NUMBER OF FLANGES
Six is the total number of discs on the rotor that support the
tines. These discs are precisely spaced to maximize tilling coverage while at
the same time reduce jamming caused by rocks and debris.
TINES PER FLANGE
The 4 inner flanges use 6 tines. The 2 out flanges uses
three inward facing tines. This configuration
reduces the impacting of dirt between the outside flanges and the side
plate ultimately wearing on the bearing seals, at the same time redirecting
the soil to the inside of the tiller instead of spilling it out the sides
of the tiller. WoodMaxx exclusive design.
TOTAL # OF TINES
30 tines are precisely spaced to maximize down pressure on
each tine as the rotor turns. They are also spaced to allow rocks and large
debris to be easily expelled.
Self-sharpening C-shaped. Compared to L- shaped,
the C- shape is more efficient, and requires less HP to dig into the soil.
The gradual C-shape is stronger than the sharp bend of the L-shaped blades.
BLADE (TINES) MATERIAL
.25" 60si2mn, spring steel, (American standard: A29M) formed,
heat treated, and quenched in oil. These blades are self-sharpening and
made to last.
3" diameter 5/16" wall tube. Large tube diameter adds strength
ROTOR SWING DIAMETER
19-1/2" diameter. Large swing diameter allows for deep digging.
ROTOR SHAFT SPEED
540 RPM PTO input speed = 210 RPM rotor shaft speed. The rotor
speed is matched with the number of tines to reach the ideal torque
required to tear through the earth.
Shaped and formed 5/32", .16", 8 gauge. Heavy formed Q-235
(American standard ASTM A-36) structural steel plate. Forming allows for
additional strength and rigidity.
SIDE PLATE MATERIAL
5/16", .32". Heavy Q-235(American standard ASTM a-36)
structural steel plate; think steel to ensure structural integrity of the
unit during heavy use.
Keeps dirt in and maintains a level finish. The deflector is
shaped and formed for additional strength. Adjustable deflector level
allows for various finish results.
ASAE 1- 3/8" - 6 spline shaft, proven cast iron, oil bath
gearbox; ratio is 1.69:1.
Oil bath gear driven side gear drive mechanism; gear ratio is
1.52:1 gear drive is superior to chain drive in every way.
Standard 3-point hitch 14. Or category 1 quick hitch. Clevis type lower
hitch make attaching to your tractor a breeze.
T5 driveline with slip clutch torque limiter. Competitors don't use the heavy T5 type that we do. The slip clutch is a
must when tilling. The slip clutch will slip a little during heavy tilling
or when contacting an unmovable object.
Supports the tiller during storage to prevent it from tipping.
Baked on powder coat, powder coat is superior to paint.
2 year parts warranty
At WoodMaxx our service department is staffed with
professional certified technicians that inspect each machine before it is
shipped. This ensures that you get a trouble free machine from the get go.
When you need technical help or parts, our courteous staff can help you get
what you need from our fully stocked warehouse. We keep a full line of
replacement parts, and guarantee that we can ship any part within 24 hours.
Visit our website for a variety of tractor rotary tillers.
Color swatches are available. Please request if color matching is a concern.
California Residents See Prop 65 WARNINGS